: Edexcel past-paper questions pack
Back to the topic page

Work, energy and power

Past-paper questions pack

Name
Class
Date set
Date due
Score/ 255

Questions are numbered; the mark schemes (the answer key) follow on separate pages so the question pages can be handed out alone. www.alevelfurthermathstutor.com

Edexcel AS and A-level Further Maths past-paper questions since June 2018 · 60 parts, 255 marks · mark schemes follow the questions · www.alevelfurthermathstutor.com · Questions and mark schemes © Pearson Education Ltd

1. June 2025 · AS Paper 2 (Further Mechanics 1) · Q1(a) · 3 marks
1. A car of mass 1000 kg moves along a straight horizontal road at a constant speed U ms-1. The engine of the car is working at a rate of 20 kW. The total resistance to the motion of the car is modelled as a constant force of magnitude 1600 N. Using the model, (a) find the value of U. (3)
2. June 2025 · AS Paper 2 (Further Mechanics 1) · Q1(b) · 4 marks
Later on, the car moves down a straight road which is inclined to the horizontal at an angle alpha , where sin alpha = 1 The total resistance to the motion of the car is again modelled as a constant force of magnitude 1600 N. At the instant when the engine of the car is working at a rate of 20 kW and the speed of the car is 8 m s-1, the acceleration of the car is a m s-2 Using the model, (b) find the value of a. (4)
3. June 2025 · AS Paper 2 (Further Mechanics 1) · Q1(c) · 1 marks
(c) State one improvement to the model that would make it more realistic. (1)
4. June 2025 · AS Paper 2 (Further Mechanics 1) · Q3(a) · 3 marks
3. A plane is inclined to the horizontal at an angle alpha , where tan alpha = 4 . A small block of mass m is held at a point A on the plane and released from rest. Initially the block is modelled as a particle, air resistance is modelled as being negligible and the plane is modelled as being smooth. (a) Using the model and the principle of conservation of mechanical energy, find the distance of the block from A at the instant when the speed of the block is 7ms-1 (3)
5. June 2025 · AS Paper 2 (Further Mechanics 1) · Q3(b) · 3 marks
In a refined model, the block is again modelled as a particle and air resistance is modelled as being negligible, but the plane is modelled as being rough with the coefficient of friction between the block and the plane being 2 Using the refined model, (b) find, in terms of m and g, the magnitude of the frictional force acting on the block as it slides down the plane, (3)
6. June 2025 · AS Paper 2 (Further Mechanics 1) · Q3(c) · 4 marks
(c) find, using the work-energy principle, the distance of the block from A at the instant when the speed of the block is 7 ms-1 (4)
7. June 2025 · Paper 3C (Further Mechanics 1) · Q2(a) · 4 marks
2. A van of mass 900kg is moving along a straight horizontal road. When the speed of the van is v ms-1, the resistance to the motion of the van is modelled as a force of magnitude 50v N. The engine of the van is working at a constant rate of 12 kW. At the instant when the speed of the van is V ms-1, the acceleration of the van is 0 2 . ms- Using the model, (a) find the value of V. (4)
8. June 2025 · Paper 3C (Further Mechanics 1) · Q2(b) · 4 marks
Later on, the van is moving up a straight road that is inclined at an angle alpha to the alpha O 1 horizontal, where sin 12 When the speed of the van is v ms-1, the resistance to the motion of the van from non-gravitational forces is modelled as a force of magnitude 50v N. When the van has constant speed U ms-1, the engine of the van is working at a constant rate of 15kW. Using the model, (b) find the value of U. (4)
9. June 2025 · Paper 3C (Further Mechanics 1) · Q4(a) · 3 marks
4. B 8 ms-1 A 18 m theta Figure 1 A rough straight ramp is fixed to horizontal ground. The ramp is inclined at an angle theta theta O 1 to the horizontal, where sin 14 The points A and B are on a line of greatest slope of the ramp with AB = 18 m and B above A, as shown in Figure 1. A package of mass 0.5 kg is projected up the ramp from A with speed 8 m s- and comes to instantaneous rest at B. The work done against friction as the package moves from A to B is W joules. The package is modelled as a particle and air resistance is ignored. (a) Use the work-energy principle to show that W = 9.7 (3)
10. June 2025 · Paper 3C (Further Mechanics 1) · Q4(b) · 4 marks
The coefficient of friction between the package and the ramp is μ (b) Find the value of μ (4)
11. June 2025 · Paper 3C (Further Mechanics 1) · Q6(c) · 3 marks
(c) Use the principle of conservation of mechanical energy to find the speed of P at the instant it passes B. (3)
12. June 2024 · AS Paper 2 (Further Mechanics 1) · Q2(a) · 4 marks
2. A lorry has mass 5000 kg. In all circumstances, when the speed of the lorry is v m s –1 , the resistance to motion of the lorry from non-gravitational forces is modelled as having magnitude 490v newtons. The lorry moves along a straight horizontal road at 12 m s –1 , with its engine working at a constant rate of 84 kW. Using the model, (a) find the acceleration of the lorry. (4)
13. June 2024 · AS Paper 2 (Further Mechanics 1) · Q2(b) · 4 marks
Another straight road is inclined to the horizontal at an angle alpha where sin alpha = With its engine again working at a constant rate of 84 kW, the lorry can maintain a constant speed of V m s –1 up the road. Using the model, (b) find the value of V. (4)
14. June 2024 · AS Paper 2 (Further Mechanics 1) · Q3(a) · 4 marks
3. A B theta 2gh h Figure 1 Figure 1 shows part of the end elevation of a building which sits on horizontal ground. The side of the building is vertical and has height h. A small stone of mass m is at rest on the roof of the building at the point A. The stone slides from rest down a line of greatest slope of the roof and reaches the edge B of the roof with speed 2gh The stone then moves under gravity before hitting the ground with speed W. In a model of the motion of the stone from B to the ground • the stone is modelled as a particle • air resistance is ignored Using the principle of conservation of mechanical energy and the model, (a) find W in terms of g and h. (4)
15. June 2024 · AS Paper 2 (Further Mechanics 1) · Q3(b) · 3 marks
In a model of the motion of the stone from A to B • the stone is modelled as a particle of mass m • air resistance is ignored • the roof of the building is modelled as a rough plane inclined to the horizontal at an angle theta , where tan theta = 3 the coefficient of friction between the stone and the roof is 1 • • AB = d Using this model, (b) find, in terms of m and g, the magnitude of the frictional force acting on the stone as it slides down the roof, (3)
16. June 2024 · AS Paper 2 (Further Mechanics 1) · Q3(c) · 5 marks
(c) use the work–energy principle to find d in terms of h. (5)
17. June 2024 · Paper 3C (Further Mechanics 1) · Q1(a) · 3 marks
1. [In this question, i and j are horizontal perpendicular unit vectors.] A particle A has mass 3 kg and a particle B has mass 2 kg. The particles are moving on a smooth horizontal plane when they collide directly. Immediately before the collision, the velocity of A is (3i – j) m s –1 and the velocity of B is (–6i + 2j) m s –1 : i j m s Immediately after the collision the velocity of A is 3 –1 (a) Find the total kinetic energy of the two particles before the collision. (3)
18. June 2024 · Paper 3C (Further Mechanics 1) · Q2(a) · 3 marks
2. A rough plane is inclined to the horizontal at an angle theta , where tan theta = 3 A particle P of mass m is at rest at a point on the plane. The particle is projected up the plane with speed 2ag The particle moves up a line of greatest slope of the plane and comes to instantaneous rest after moving a distance d. The coefficient of friction between P and the plane is 1 (a) Show that the magnitude of the frictional force acting on P as it moves up the plane mg is 4 (3)
19. June 2024 · Paper 3C (Further Mechanics 1) · Q2(b) · 4 marks
Air resistance is assumed to be negligible. Using the work-energy principle, (b) find d in terms of a. (4)
20. June 2024 · Paper 3C (Further Mechanics 1) · Q3(a) · 3 marks
3. A car of mass 1000 kg moves in a straight line along a horizontal road at a constant speed of 72 km h –1 • The resistance to the motion of the car is modelled as a constant force of magnitude 900 N The engine of the car is working at a constant rate of P kW. Using the model, (a) find the value of P. (3)
21. June 2024 · Paper 3C (Further Mechanics 1) · Q3(b) · 4 marks
The car now travels in a straight line up a road which is inclined to the horizontal at an angle alpha , where sin alpha = 2 • In a refined model, the resistance to the motion of the car from non-gravitational forces is now modelled as a force of magnitude 20v newtons, where v m s –1 is the speed of the car At the instant when the engine of the car is working at a constant rate of 30 kW and the car is moving up the road at 10 m s –1 , the acceleration of the car is a m s –2 Using the refined model, (b) find the value of a. (4)
22. June 2024 · Paper 3C (Further Mechanics 1) · Q3(c) · 5 marks
Later on, when the engine of the car is again working at a constant rate of 30 kW, the car is moving up the road at a constant speed U m s –1 Using the refined model, (c) find the value of U. (5)
23. June 2024 · Paper 3C (Further Mechanics 1) · Q5 · 7 marks
5. A light elastic string has natural length 2a and modulus of elasticity 2mg. One end of the string is attached to a fixed point A on a horizontal ceiling. The other end is attached to a particle P of mass m. The particle P hangs in equilibrium at the point E, where AE = 3a. The particle P is then projected vertically downwards from E with speed 3 ag Air resistance is assumed to be negligible. Find the elastic energy stored in the string, when P first comes to instantaneous rest. Give your answer in the form kmga, where k is a constant to be found. (7)
24. June 2023 · AS Paper 2 (Further Mechanics 1) · Q2(a) · 4 marks
2. A racing car of mass 750 kg is moving along a straight horizontal road at a constant speed of U km h–1. The engine of the racing car is working at a constant rate of 60 kW. The resistance to the motion of the racing car is modelled as a force of magnitude 37.5v N, where v m s–1 is the speed of the racing car. Using the model, (a) find the value of U (4)
25. June 2023 · AS Paper 2 (Further Mechanics 1) · Q2(b) · 4 marks
Later on, the racing car is accelerating up a straight road which is inclined to the horizontal at an angle alpha , where sin alpha = 5 49 . The engine of the racing car is working at a constant rate of 60 kW. The total resistance to the motion of the racing car from non-gravitational forces is modelled as a force of magnitude 37.5v N, where v m s–1 is the speed of the racing car. At the instant when the acceleration of the racing car is 2 m s–2, the speed of the racing car is V m s–1 Using the model, (b) find the value of V (4)
26. June 2023 · AS Paper 2 (Further Mechanics 1) · Q3(a) · 4 marks
3. A stone of mass 0.5 kg is projected vertically upwards with a speed U m s–1 from a point A. The point A is 2.5 m above horizontal ground. The speed of the stone as it hits the ground is 25 m s–1 The motion of the stone from the instant it is projected from A until the instant it hits the ground is modelled as that of a particle moving freely under gravity. (a) Use the model and the principle of conservation of mechanical energy to find the value of U. (4)
27. June 2023 · AS Paper 2 (Further Mechanics 1) · Q3(b) · 1 marks
In reality, the stone will be subject to air resistance as it moves from A to the ground. (b) State how this would affect your answer to part (a). (1)
28. June 2023 · AS Paper 2 (Further Mechanics 1) · Q3(c) · 5 marks
The ground is soft and the stone sinks a vertical distance d cm into the ground. The resistive force exerted on the stone by the ground is modelled as a constant force of magnitude 2000 N and the stone is modelled as a particle. (c) Use the model and the work-energy principle to find the value of d, giving your answer to 3 significant figures. (5)
29. June 2023 · Paper 3C (Further Mechanics 1) · Q2(a) · 3 marks
2. A car of mass 1000 kg moves in a straight line along a horizontal road at a constant speed U m s-1. The resistance to the motion of the car is a constant force of magnitude 400 N. The engine of the car is working at a constant rate of 16 kW. (a) Find the value of U. (3)
30. June 2023 · Paper 3C (Further Mechanics 1) · Q2(b) · 5 marks
The car now pulls a trailer of mass 600 kg in a straight line along the road using a tow rope which is parallel to the direction of motion. The resistance to the motion of the car is again a constant force of magnitude 400 N. The resistance to the motion of the trailer is a constant force of magnitude 300 N. The engine of the car is working at a constant rate of 16 kW. The tow rope is modelled as being light and inextensible. Using the model, (b) find the tension in the tow rope at the instant when the speed of the car is 20 3 m s-1 (5)
31. June 2023 · Paper 3C (Further Mechanics 1) · Q4(b) · 7 marks
Particle P is now pulled vertically downwards to the point A, where OA = 4a, and released from rest. The resistance to the motion of P is a constant force of magnitude 1 4 mg. (b) Find, in terms of a and g, the speed of P after it has moved a distance a. (7)
32. June 2022 · AS Paper 2 (Further Mechanics 1) · Q1 · 5 marks
1. A car of mass 1200 kg moves up a straight road that is inclined to the horizontal at an angle alpha , where sin alpha = 1 The total resistance to the motion of the car from non-gravitational forces is modelled as a constant force of magnitude R newtons. At the instant when the engine of the car is working at a rate of 32 kW and the speed of the car is 20 m s–1 , the acceleration of the car is 0.5 m s–2 Find the value of R (5)
33. June 2022 · AS Paper 2 (Further Mechanics 1) · Q3(a) · 4 marks
3. A plane is inclined to the horizontal at an angle alpha , where tan alpha = 3 A particle P is held at rest at a point A on the plane. The particle P is then projected with speed 25 m s–1 from A, up a line of greatest slope of the plane. In an initial model, the plane is modelled as being smooth and air resistance is modelled as being negligible. Using this model and the principle of conservation of mechanical energy, (a) find the speed of P at the instant when it has travelled a distance 25 6 m up the plane from A. (4)
34. June 2022 · AS Paper 2 (Further Mechanics 1) · Q3(b) · 8 marks
In a refined model, the plane is now modelled as being rough, with the coefficient of friction between P and the plane being 3 Air resistance is still modelled as being negligible. Using this refined model and the work-energy principle, (b) find the speed of P at the instant when it has travelled a distance 25 6 m up the plane from A. (8)
35. June 2022 · Paper 3C (Further Mechanics 1) · Q2 · 8 marks
2. 600 kg 150 kg alpha Figure 1 A van of mass 600 kg is moving up a straight road which is inclined at an angle alpha to the horizontal, where sin alpha = 1 15 . The van is towing a trailer of mass 150 kg. The van is attached to the trailer by a towbar which is parallel to the direction of motion of the van and the trailer, as shown in Figure 1. The resistance to the motion of the van from non-gravitational forces is modelled as a constant force of magnitude 200 N. The resistance to the motion of the trailer from non-gravitational forces is modelled as a constant force of magnitude 100 N. The towbar is modelled as a light rod. The engine of the van is working at a constant rate of 12 kW. Find the tension in the towbar at the instant when the speed of the van is 9 m s–1 (8)
36. June 2022 · Paper 3C (Further Mechanics 1) · Q6(a) · 3 marks
6. P A 2 kg 4 kg B 3 m theta Figure 4 Two blocks, A and B, of masses 2 kg and 4 kg respectively are attached to the ends of a light inextensible string. Initially A is held on a fixed rough plane. The plane is inclined to horizontal ground at an angle theta , where tan theta = 3 The string passes over a small smooth light pulley P that is fixed at the top of the plane. The part of the string from A to P is parallel to a line of greatest slope of the plane. Block A is held on the plane with the distance AP greater than 3 m. Block B hangs freely below P at a distance of 3 m above the ground, as shown in Figure 4. The coefficient of friction between A and the plane is μ Block A is released from rest with the string taut. By modelling the blocks as particles, (a) find the potential energy lost by the whole system as a result of B falling 3 m. (3)
37. June 2022 · Paper 3C (Further Mechanics 1) · Q6(b) · 6 marks
Given that the speed of B at the instant it hits the ground is 4.5 m s–1 and ignoring air resistance, (b) use the work-energy principle to find the value of μ (6)
38. June 2022 · Paper 3C (Further Mechanics 1) · Q6(c) · 4 marks
After B hits the ground, A continues to move up the plane but does not reach the pulley in the subsequent motion. Block A comes to instantaneous rest after moving a total distance of (3 + d) m from its point of release. Ignoring air resistance, (c) use the work-energy principle to find the value of d (4)
39. Nov 2021 · Paper 3C (Further Mechanics 1) · Q1(a) · 5 marks
1. A van of mass 900 kg is moving along a straight horizontal road. At the instant when the speed of the van is v m s-1, the resistance to the motion of the van is modelled as a force of magnitude (500 + 7v) N. When the engine of the van is working at a constant rate of 18 kW, the van is moving along the road at a constant speed V m s-1 (a) Find the value of V. (5)
40. Nov 2021 · Paper 3C (Further Mechanics 1) · Q1(b) · 4 marks
Later on, the van is moving up a straight road that is inclined to the horizontal at an angle theta , where sin theta = 1 At the instant when the speed of the van is v m s-1, the resistance to the motion of the van from non-gravitational forces is modelled as a force of magnitude (500 + 7v) N. The engine of the van is again working at a constant rate of 18 kW. (b) Find the acceleration of the van at the instant when v = 15 (4)
41. Nov 2021 · Paper 3C (Further Mechanics 1) · Q6(b) · 6 marks
(b) find, in terms of g and l , the speed of P at the instant when the spring first reaches its natural length of 3l . (6)
42. Oct 2020 · AS Paper 2 (Further Mechanics 1) · Q2(a) · 1 marks
2. A car of mass 1000 kg moves along a straight horizontal road. In all circumstances, when the speed of the car is v m s–1, the resistance to the motion of the car is modelled as a force of magnitude cv2 N, where c is a constant. The maximum power that can be developed by the engine of the car is 50 kW. At the instant when the speed of the car is 72 km h–1 and the engine is working at its maximum power, the acceleration of the car is 2.25 m s–2 (a) Convert 72 km h–1 into m s–1 (1)
43. Oct 2020 · AS Paper 2 (Further Mechanics 1) · Q2(b) · 7 marks
(b) Find the acceleration of the car at the instant when the speed of the car is 144 km h–1 and the engine is working at its maximum power. (7)
44. Oct 2020 · AS Paper 2 (Further Mechanics 1) · Q2(c) · 4 marks
The maximum speed of the car when the engine is working at its maximum power is V km h–1. (c) Find, to the nearest whole number, the value of V. (4)
45. Oct 2020 · AS Paper 2 (Further Mechanics 1) · Q4(a) · 5 marks
4. A small ball, of mass m, is thrown vertically upwards with speed 8gH from a point O on a smooth horizontal floor. The ball moves towards a smooth horizontal ceiling that is a vertical distance H above O. The coefficient of restitution between the ball and the ceiling is 1 In a model of the motion of the ball, it is assumed that the ball, as it moves up or down, is subject to air resistance of constant magnitude 1 2 mg. Using this model, (a) use the work-energy principle to find, in terms of g and H, the speed of the ball immediately before it strikes the ceiling, (5)
46. Oct 2020 · AS Paper 2 (Further Mechanics 1) · Q4(b) · 5 marks
(b) find, in terms of g and H, the speed of the ball immediately before it strikes the floor at O for the first time. (5)
47. Oct 2020 · Paper 3C (Further Mechanics 1) · Q2(a) · 4 marks
2. A truck of mass 1200 kg is moving along a straight horizontal road. At the instant when the speed of the truck is v m s–1, the resistance to the motion of the truck is modelled as a force of magnitude (900 + 9v) N. The engine of the truck is working at a constant rate of 25 kW. (a) Find the deceleration of the truck at the instant when v = 25 (4)
48. Oct 2020 · Paper 3C (Further Mechanics 1) · Q2(b) · 5 marks
Later on, the truck is moving up a straight road that is inclined at an angle theta to the horizontal, where sin theta = 1 At the instant when the speed of the truck is v m s–1, the resistance to the motion of the truck from non‑gravitational forces is modelled as a force of magnitude (900 + 9v) N. When the engine of the truck is working at a constant rate of 25 kW the truck is moving up the road at a constant speed of V m s–1. (b) Find the value of V. (5)
49. Oct 2020 · Paper 3C (Further Mechanics 1) · Q6(a) · 6 marks
6. A light elastic string with natural length l and modulus of elasticity kmg has one end attached to a fixed point A on a rough inclined plane. The other end of the string is attached to a package of mass m. The plane is inclined at an angle theta to the horizontal, where tan theta = 5 The package is initially held at A. The package is then projected with speed 6gl up a line of greatest slope of the plane and first comes to rest at the point B, where AB = 3l. The coefficient of friction between the package and the plane is 1 By modelling the package as a particle, (a) show that k = 15 (6)
50. June 2019 · AS Paper 2 (Further Mechanics 1) · Q1(a) · 4 marks
1. A lorry of mass 16 000 kg moves along a straight horizontal road. ms- The lorry moves at a constant speed of 25 In an initial model for the motion of the lorry, the resistance to the motion of the lorry is modelled as having constant magnitude 16 000 N. (a) Show that the engine of the lorry is working at a rate of 400 kW. (4)
51. June 2019 · AS Paper 2 (Further Mechanics 1) · Q1(b) · 6 marks
The model for the motion of the lorry along the same road is now refined so that when the speed of the lorry along the same road is V ms-1, the resistance to the motion of the lorry is modelled as having magnitude 640V newtons. Assuming that the engine of the lorry is working at the same rate of 400 kW (b) use the refined model to find the speed of the lorry when it is accelerating at 2.1 ms-2 (6)
52. June 2019 · AS Paper 2 (Further Mechanics 1) · Q3 · 7 marks
3. A particle, P, of mass m kg is projected with speed 5 ms-1 down a line of greatest slope of a rough plane. The plane is inclined to the horizontal at an angle Į, where sin alpha = 3 The total resistance to the motion of P is a force of magnitude 1 5 mg Use the work-energy principle to find the speed of P at the instant when it has moved a distance 8 m down the plane from the point of projection. (7)
53. June 2019 · Paper 3C (Further Mechanics 1) · Q4(a) · 4 marks
4. A car of mass 600 kg pulls a trailer of mass 150 kg along a straight horizontal road. The trailer is connected to the car by a light inextensible towbar, which is parallel to the direction of motion of the car. The resistance to the motion of the trailer is modelled as a constant force of magnitude 200 N. At the instant when the speed of the car is v m s–1, the resistance to the motion of the car is modelled as a force of magnitude (200 + ) N, where is a constant. When the engine of the car is working at a constant rate of 15 kW, the car is moving at a constant speed of 25 m s–1 (a) Show that = 8 (4)
54. June 2019 · Paper 3C (Further Mechanics 1) · Q4(b) · 4 marks
Later on, the car is pulling the trailer up a straight road inclined at an angle to the horizontal, where sin = The resistance to the motion of the trailer from non-gravitational forces is modelled as a constant force of magnitude 200 N at all times. At the instant when the speed of the car is v m s–1, the resistance to the motion of the car from non-gravitational forces is modelled as a force of magnitude (200 + 8v) N. The engine of the car is again working at a constant rate of 15 kW. When v = 10, the towbar breaks. The trailer comes to instantaneous rest after moving a distance d metres up the road from the point where the towbar broke. (b) Find the acceleration of the car immediately after the towbar breaks. (4)
55. June 2019 · Paper 3C (Further Mechanics 1) · Q4(c) · 4 marks
(c) Use the work-energy principle to find the value of d. (4)
56. June 2018 · AS Paper 2 (Further Mechanics 1) · Q2(a) · 4 marks
2. B 2.5 m A theta Figure 1 Figure 1 shows a ramp inclined at an angle theta to the horizontal, where sin theta = 2 A parcel of mass 4 kg is projected, with speed 5 m s–1, from a point A on the ramp. The parcel moves up a line of greatest slope of the ramp and first comes to instantaneous rest at the point B, where AB = 2.5 m. The parcel is modelled as a particle. The total resistance to the motion of the parcel from non‑gravitational forces is modelled as a constant force of magnitude R newtons. (a) Use the work‑energy principle to show that R = 8.8 (4)
57. June 2018 · AS Paper 2 (Further Mechanics 1) · Q2(b) · 3 marks
After coming to instantaneous rest at B, the parcel slides back down the ramp. The total resistance to the motion of the particle is modelled as a constant force of magnitude 8.8 N. (b) Find the speed of the parcel at the instant it returns to A. (3)
58. June 2018 · AS Paper 2 (Further Mechanics 1) · Q2(c) · 2 marks
(c) Suggest two improvements that could be made to the model. (2)
59. June 2018 · AS Paper 2 (Further Mechanics 1) · Q3(a) · 4 marks
3. A van of mass 750 kg is moving along a straight horizontal road. At the instant when the van is moving at v m s–1, the resistance to the motion of the van is modelled as a force of magnitude λv N, where λ is a constant. The engine of the van is working at a constant rate of 18 kW. At the instant when v = 15, the acceleration of the van is 0.6 m s–2 (a) Show that λ = 50 (4)
60. June 2018 · AS Paper 2 (Further Mechanics 1) · Q3(b) · 5 marks
The van now moves up a straight road inclined at an angle to the horizontal, where sin alpha = 1 At the instant when the van is moving at v m s–1, the resistance to the motion of the van from non‑gravitational forces is modelled as a force of magnitude 50v N. When the engine of the van is working at a constant rate of 12 kW, the van is moving at a constant speed V m s–1 (b) Find the value of V. (5)

Mark schemes

Each mark scheme shows the whole question; the parts on this topic are the ones listed above.

June 2025 · AS Paper 2 (Further Mechanics 1) · Q1
Mark scheme June 2025 Paper 2 (Further Mechanics 1) Q1(c)
June 2025 · AS Paper 2 (Further Mechanics 1) · Q3
Mark scheme June 2025 Paper 2 (Further Mechanics 1) Q3(c)
June 2025 · Paper 3C (Further Mechanics 1) · Q2
Mark scheme June 2025 Paper 3C (Further Mechanics 1) Q2(b)
June 2025 · Paper 3C (Further Mechanics 1) · Q4
Mark scheme June 2025 Paper 3C (Further Mechanics 1) Q4(b)
June 2025 · Paper 3C (Further Mechanics 1) · Q6
Mark scheme June 2025 Paper 3C (Further Mechanics 1) Q6(c)
June 2024 · AS Paper 2 (Further Mechanics 1) · Q2
Mark scheme June 2024 Paper 2 (Further Mechanics 1) Q2(b)
June 2024 · AS Paper 2 (Further Mechanics 1) · Q3
Mark scheme June 2024 Paper 2 (Further Mechanics 1) Q3(c)
June 2024 · Paper 3C (Further Mechanics 1) · Q1
Mark scheme June 2024 Paper 3C (Further Mechanics 1) Q1(a)
June 2024 · Paper 3C (Further Mechanics 1) · Q2
Mark scheme June 2024 Paper 3C (Further Mechanics 1) Q2(b)
June 2024 · Paper 3C (Further Mechanics 1) · Q3
Mark scheme June 2024 Paper 3C (Further Mechanics 1) Q3(c)
June 2024 · Paper 3C (Further Mechanics 1) · Q5
Mark scheme June 2024 Paper 3C (Further Mechanics 1) Q5
June 2023 · AS Paper 2 (Further Mechanics 1) · Q2
Mark scheme June 2023 Paper 2 (Further Mechanics 1) Q2(b)
June 2023 · AS Paper 2 (Further Mechanics 1) · Q3
Mark scheme June 2023 Paper 2 (Further Mechanics 1) Q3(c)
June 2023 · Paper 3C (Further Mechanics 1) · Q2
Mark scheme June 2023 Paper 3C (Further Mechanics 1) Q2(b)
June 2023 · Paper 3C (Further Mechanics 1) · Q4
Mark scheme June 2023 Paper 3C (Further Mechanics 1) Q4(b)
June 2022 · AS Paper 2 (Further Mechanics 1) · Q1
Mark scheme June 2022 Paper 2 (Further Mechanics 1) Q1
June 2022 · AS Paper 2 (Further Mechanics 1) · Q3
Mark scheme June 2022 Paper 2 (Further Mechanics 1) Q3(b)
June 2022 · Paper 3C (Further Mechanics 1) · Q2
Mark scheme June 2022 Paper 3C (Further Mechanics 1) Q2
June 2022 · Paper 3C (Further Mechanics 1) · Q6
Mark scheme June 2022 Paper 3C (Further Mechanics 1) Q6(c)
Nov 2021 · Paper 3C (Further Mechanics 1) · Q1
Mark scheme Nov 2021 Paper 3C (Further Mechanics 1) Q1(b)
Nov 2021 · Paper 3C (Further Mechanics 1) · Q6
Mark scheme Nov 2021 Paper 3C (Further Mechanics 1) Q6(b)
Oct 2020 · AS Paper 2 (Further Mechanics 1) · Q2
Mark scheme Oct 2020 Paper 2 (Further Mechanics 1) Q2(c)
Oct 2020 · AS Paper 2 (Further Mechanics 1) · Q4
Mark scheme Oct 2020 Paper 2 (Further Mechanics 1) Q4(b)
Oct 2020 · Paper 3C (Further Mechanics 1) · Q2
Mark scheme Oct 2020 Paper 3C (Further Mechanics 1) Q2(b)
Oct 2020 · Paper 3C (Further Mechanics 1) · Q6
Mark scheme Oct 2020 Paper 3C (Further Mechanics 1) Q6(a)
June 2019 · AS Paper 2 (Further Mechanics 1) · Q1
Mark scheme June 2019 Paper 2 (Further Mechanics 1) Q1(b)
June 2019 · AS Paper 2 (Further Mechanics 1) · Q3
Mark scheme June 2019 Paper 2 (Further Mechanics 1) Q3
June 2019 · Paper 3C (Further Mechanics 1) · Q4
Mark scheme June 2019 Paper 3C (Further Mechanics 1) Q4(c)
June 2018 · AS Paper 2 (Further Mechanics 1) · Q2
Mark scheme June 2018 Paper 2 (Further Mechanics 1) Q2(c)
June 2018 · AS Paper 2 (Further Mechanics 1) · Q3
Mark scheme June 2018 Paper 2 (Further Mechanics 1) Q3(b)